Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Just about everyone may have their personal assumption when it comes to Installing A Bathtub.
Setting up a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately tough task. If the old tub is conveniently available, the task can relocate rapidly; if you have to open up a wall surface to remove the old tub and position the new tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to vacate the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the work and are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to think about employing one before you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you set up a brand-new bath tub in your bathroom if you have actually already purchased a new bathtub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and also product checklist must comprise the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bath must be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly bothersome due to the limited access that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for position. The wood boards are handy in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
Activate the water supply and check all joints and brand-new pipework for leakages as well as tighten them if needed. Load the bathtub and also examine the overflow electrical outlet and also the normal outlet for leakages.
Lastly, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the tub ought to wait up until the bathtub has been used a minimum of when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making certain that the washing machines remain in location between the faucet and also the sink. Safeguard the tap in place with the producer given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap ports. The previous kind must be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to crack an inflexible seal, causing the water to permeate the wall surface in between the bath and also the tiling, bring about issues with moisture and also possible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your components and also fittings. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can break fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the marketplace. It is advisable to fit the floor tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that review about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the internet. Those who enjoyed our page if you please make sure you remember to share it. Kudos for your time. Visit us again soon.
This Post Report this page